wE SeLL oNLy ScaNNerS and cHiPS. SoftWare wE gIve fOR FrEE

.OPEL - CAN - USB -Scanner

OP - COM v.09.07.14

Last UpDated 23 November 2009



$240 for the Scanner & SoftWare is FREE of Charge

Last SofWare is v. 09.07.14

Last FirmWare is v. 1.39

* * *

Version 09.07.14 Full ENG/RUS - Working OP-COM CAN-USB
( ТОЛЬКО для адаптеров выпущенных c 20 НОЯБРЯ 2009 )
The Initial SetUp with USB-drivers and Manuals inside support

Version 08.01.14 Full ENG/RUS - Working OP-COM CAN-USB
( ТОЛЬКО для адаптеров выпущенных c 05 МАРТА 2009 до 20 НОЯБРЯ 2009 )
The Initial SetUp with USB-drivers and Manuals inside + RUS support

Dowload Version 07.10.10 Full - Working OP-COM CAN-USB
( ТОЛЬКО для адаптеров выпущенных с 01 ОКТЯБРЯ 2008 до 05 МАРТА 2009)
The Initial SetUp with USB-drivers and Manuals inside + RUS support

DownLoad OLD Full - Working OP-COM v. 07.05.09 CAN-USB
( для адаптеров выпущенных до 01 ОКТЯБРЯ 2008)

!!! ATTENTION !!! !!! ВНИМАНИЕ !!!
DO NOT UpDate the Scanner with the soft apart from this page ONLY !

Scanner can be destroied with the software from third-parties. BE WARE !

Не обновляйте адаптер версиями скаченными с других сайтов !

Гарантируется работоспособность сканера ТОЛЬКО с программным обеспечением, скаченным с этой страницы

It is full working HardWare scanner that is compatible with SoftWare of Auto-M3Ltd

$240 for the Scanner & SoftWare is FREE of Charge

OP-COM - is FREE PC based OPEL diagnostic software form Auto-M3Ltd

It works with PIC-controller based scanner. The scanner is designed and produced by OBDtool.Org

It covers almost all Opel cars, even new cars with
CAN-BUS based diagnostic, such as Vectra-C, Astra-H, Zafira-B.

Программный аналог дилерского сканера TECH-2. Привязывает ключи, делает синхру ИММО и Моторного Блока

Работает по CAN !

The program lets you to read out and clear fault codes, shows you live data, lets you to perform output test, and supports remote, and key programming.

The program supports many control units, like Engine, Automatic Transmission, ABS, Airbag, Engine Cooling module, Instrument Cluster, Electronic Climate Control, Body Control Unit, just to name a few examples.

Since Opel uses many pin in the OBD connector, the diagnostic interface works as a multiplexer, and selects the appropriate pin for communication.

PIN3, PIN7, PIN8, PIN12 = Serial Link (ISO9141, KW81, KW82, KWP2000)
Fault codes will be shown with all available information:

Full fault code text description
Full status information (Present, Not present, Intermittent)

You can print out, save, or copy the fault codes to any other application.
From the fault codes window, you can go directly to the measuring blocks window.
The program shows you measuring block information on many control module, you can choose anything from the list on your own. The program is capable of showing 8 measuring block parameter simultaneously. The sample rate is depends mostly on the communication protocol. For example, older system, like Omega-B X 25 DT Engine (ISO-9141-2) can be very slow, during communication, while newer Multec, or Bosch units are faster (using KWP-2000), and the newest CAN based control units are very fast!
You can also run output tests on many controllers.
HSCAN  - Dual-wire, High Speed CAN-BUS, 500 kbps
MSCAN - Dual-wire, Medium Speed CAN-BUS, 95 kbps
SWCAN - Single-wire, Low Speed CAN-BUS, 33.3 kbps
You will get a feedback on the state of the activated output. This will helps you to find the failed components more easily.
With OP-COM, you can learn keys to immobiliser, and remote keys to the central door locking, or alarm.
You can also reset, and program the following immobiliser related items: ECM, BCM, IPC.
You will need the vehicle security code, which can be found
on the CAR-PASS.
You can also reset, and program the Service interval reminder on Astra-G, Zafira, Corsa-C, Meriva, Tigra-B
You can code SAB6, and SAB8 airbags with the software.
The diagnostic inteface is USB port based, so there will be NO COMPATIBILITY ISSUES, with serial to USB converters.
The speed of the communication over the USB-BUS is enough to handle the awesome speed of the High-Speed CAN-BUS systems, which is currently 500kbps. This is the main reason, why only the USB port based interface is available for CAN-BUS.

Compared to the TECH2, which is the dealers tool (with a 32 MB card+CANdi interface), the price of OP-COM is quite affordable.

OP-COM is under continous development, new version will be availabe approximately every 3-4 month.

OP-COM is available in English and Russian

How to Order and Pay ? Terms of Payment and Delivery Как Заказать и Оплатить ?

Сurrency Convertor http://www.xe.com/ucc Конвертор Валют

wE SenD Our-Made ScaNNers WorLD WiDe


SupPort SoftWare


keywords: uniscan autoscanner carsoft free bmwscan bmw carsoft v.6.5 cracked mersrdesscan mersedes xeltek scantool obd2 obd-II obd-2 iso pwm vpw subaru select monitor j1962 kwp-2000 kwp 2000 key word protocol subaru impreza protocol chip chip-tuning tuning chiptuning free download new version crack keygen generator serial number free id ID programmer kit sircuit scheme free auto bmw mersedes subaru uniscan 2.90 new version crack vehicle explorer scantool scantool.net elm chip pdf race fuel high octane 323 322 320 atmel free dump hex russian new version scanner pc lpt ocsilloscope digital download scheme impreza chip tuning

Hosted by uCoz